Ford Fusion: Capacities and Specifications / Capacities and Specifications - 2.5L
Use oil and fluid that meets the defined specification and viscosity grade.
If you do not use oil and fluid that meets the defined specification and viscosity grade, it could result in:
- Component damage that your vehicle warranty does not cover.
- Longer engine cranking periods.
- Increased emission levels.
- Reduced engine performance.
- Reduced fuel economy.
- Reduced brake performance.
Air Conditioning System
WARNING: The air conditioning refrigerant system contains refrigerant under high pressure. Only qualified personnel should service the air conditioning refrigerant system. Opening the air conditioning refrigerant system can cause personal injury.
Capacities
Materials
Automatic Transmission
Note: Automatic transmissions that require MERCON® LV transmission fluid should only use MERCON® LV transmission fluid. The use of any other fluid could cause transmission damage.
Capacities
1 Approximate dry fill capacity. Actual amount may vary during fluid changes.
Materials
Engine Coolant
Capacities
Materials
Engine Oil
An oil that displays this symbol conforms to current engine, emission system and fuel economy performance standards of ILSAC.
We recommend Motorcraft® motor oil for your vehicle. If Motorcraft® oil is not available, use motor oils of the recommended viscosity grade that meet API SN PLUS requirements and display the API Certification Mark for gasoline engines.
Capacities
Materials
Alternative Engine Oil for Extremely Cold Climates
To improve engine cold start performance, we recommend that you use the following alternative engine oil in extremely cold climates, where the ambient temperature reaches -22.0°F (-30°C) or below.
Materials
Fuel Tank
Capacities
Grease
Materials
Hydraulic Brake System
Note: We recommend using DOT 4 Low Viscosity (LV) High Performance Brake Fluid or equivalent meeting WSS-M6C65-A2. Use of any fluid other than the recommended fluid could cause reduced brake performance and not meet our performance standards. Keep brake fluid clean and dry. Contamination with dirt, water, petroleum products or other materials could result in brake system damage and possible failure.
Materials
Locks
Materials
Washer Reservoir
Capacities
Materials
Capacities and Specifications - 2.7L EcoBoost™
Use oil and fluid that meets the defined
specification and viscosity grade.
If you do not use oil and fluid that meets
the defined specification and viscosity
grade, it could result in:
Component damage that your vehicle
warranty does not cover...
Other information:
Ford Fusion 2013–2020 Service Manual: Turbine Shaft Speed (TSS) Sensor. Removal and Installation
Removal Remove the air cleaner. Refer to: Air Cleaner (303-12A Intake Air Distribution and Filtering - 1.5L EcoBoost (118kW/160PS) – I4, Removal and Installation). Refer to: Air Cleaner (303-12B Intake Air Distribution and Filtering - 2.0L EcoBoost (184kW/250PS) – MI4, Removal and Installation)...
Ford Fusion 2013–2020 Service Manual: Pinpoint Test - DTC: J. Diagnosis and Testing
B0070:11, B0070:12, B0070:13 and B0070:1A Refer to Wiring Diagrams Cell 46 for schematic and connector information. Normal Operation and Fault Conditions The RCM continuously monitors the driver seatbelt anchor pretensioner circuits for the following faults: Resistance out of range Unexpected voltage Short to ground Faulted driver seatbelt anchor pretensioner ..
Categories
- Manuals Home
- 2nd Generation Ford Fusion Owners Manual
- 2nd Generation Ford Fusion Service Manual
- Pre-Collision Assist (IF EQUIPPED)
- Electrical
- Steering Column Control Module (SCCM). Removal and Installation
- New on site
- Most important about car
Using Seatbelts During Pregnancy
WARNING: Always ride and drive with your seatback upright and properly fasten your seatbelt. Fit the lap portion of the seatbelt snugly and low across the hips. Position the shoulder portion of the seatbelt across your chest. Pregnant women must follow this practice. See the following figure.
